Influence of Inorganic Sealant in Hot and Cold Erosive Wear in Plasma Sprayed Alumina Coating

摘要:

文章预览

Plasma sprayed alumina coating is applied in many industrial applications in order to promote wear and corrosion resistance. Nonetheless, high porosity remained after deposition is a critical factor because it decreases the wear resistance. Some inorganic sealants can be used to reduce the open pores and superficial micro-cracks effect, improving the wear and corrosion resistance of alumina coatings. In this work, plasma sprayed alumina coating samples were divided into two groups: i) impregnated with inorganic sealant (AlPO4) and heat treated; ii) as deposited. Erosive wear tests were carried out in an erosion rig according to ASTM G76. The samples were subjected to an erodent flux, with impact angles of 30º up to 90º, at a velocity of 50m/s and temperatures of 25°C up to 400°C. The samples were characterized by SEM, Vickers microhardness, potentiodynamic anodic polarization and erosive wear rate. Results showed that erosive wear rate of alumina impregnated coating is lower than without the sealant. The sealed alumina coating presented higher mechanical properties; improved microstructural characteristics and the sealant promoted better lamellae contact, as can be observed by less sharpness in pits formation of microstructure.

信息:

编辑:

Pietro VINCENZINI and Ghislain MONTAVON

页数:

86-91

引用:

J. Vicenzi et al., "Influence of Inorganic Sealant in Hot and Cold Erosive Wear in Plasma Sprayed Alumina Coating", Advances in Science and Technology, Vol. 66, pp. 86-91, 2010

上线时间:

October 2010

输出:

价格:

$38.00

[1] A. Ohmori, C.J. Li, Y. Arata: Thin Solid Films. Vol 156 (1988), p.315.

[2] R. McPherson: Surf. Coat. Technol. Vol. 39–40 (1989), pp.173-180.

[3] C.L. Li, H.X. Zhao, T. Takahashi, M. Matsumura: Mater. Sci. Eng. A 308 (2001), pp.268-276.

[4] E.M. Leivo, M.S. Vippola, P.P.A. Sorsa, P.M.J. Vuoristo, T.A. Mäntylä: J. Therm. Spray Technol. Vol. 6 (1997), pp.205-210.

[5] K. Niemi, P. Sorsa, P. Vuoristo, T. Mäntylä: Proceedings of the National Thermal Spray Conference, Boston, MA, USA (1994), pp.533-536.

[6] J. Mateos, J.M. Cuetos, E. Fernández, R. Vijande: Wear 239 (2000), p.274–281.

[7] P. Kulu: J. Tribologia: Finnish J. Tribology. Vol. 4 (1989), pp.12-25.

[8] P. Kulu and R. Veinthal, Wear: Proceedings of 9th Nordic Symposium on Tribology. Vol. 1, Ed. Technical Research Centre of Finland (VTT), Espoo, Finland (2000), pp.87-95.

[9] P. Kulu, I. Hussainova and R Veinthal: Wear. Vol. 258 (2005) pp.488-496.

DOI: https://doi.org/10.1016/j.wear.2004.03.021

[10] I. Finnie: Wear. Vol. 3 (1960), pp.87-103.

[11] STANDARD ASTM G76-05. Annual Book of ASTM Standards (2005).

[12] C. M. Marques: Relação entre microestrutura e desgaste erosivo a frio e a quente em materiais cerâmicos à base de alumina (2006). Doctoral Thesis. UFRGS.

[13] J. Vicenzi: Relação entre microestrutura e erosão (a frio e a quente) de revestimentos do sistema NiCr-Cr3C2 obtidos por aspersão térmica (2007). Doctoral Thesis. UFRGS.

[14] C.M. Marques, J. Vicenzi and C.P. Bergmann: Boletin Técnico de Produção de Petróleo da petrobras. Vol. 3 (2008), pp.83-98.

[15] R. Westergård, L.C. Erickson, N. Axén, H.M. Hawthorne, S. Hogmark: Tribol. Int. Vol. 31 (1998) 271–279.

从Crossref获取数据。
这可能需要一些时间来加载。