Estimation of the Influence of Burnishing Parameters on X5CrNi18-10 Steel

摘要:

文章预览

Angular momentum pumps are very often applied in ships. Because the pumps are operating in hard conditions they are produced from cavitation wear-proof and electrochemical corrosion-resistant materials. The most common damage of pump shaft is neck wear in place where seals are mounted. Burnishing as modern finish plastic tooling method makes it possible to achieve high technological quality of elements. Due to many burnishing advantages, the method was proposed for treatment of angular momentum pumps shafts instead of finish machining (finish turning, grinding, lapping). The goal was to estimate optimal burnishing parameters that enable obtaining higher strength and the lowest roughness factor of angular momentum pumps shafts. Shaft necks were made of stainless steel type X5CrNi1810. Roller burnishing tool SRMD type produced by Yamato was used in the research work. Its axis was parallel to working shaft axis. During working, technological parameters such as force, velocity and feed were changed.

信息:

期刊:

编辑:

Andrejus H. Marcinkevičius and Algirdas V.Valiulis

页数:

300-305

DOI:

10.4028/www.scientific.net/SSP.165.300

引用:

W. Labuda and R. Starosta, "Estimation of the Influence of Burnishing Parameters on X5CrNi18-10 Steel ", Solid State Phenomena, Vol. 165, pp. 300-305, 2010

上线时间:

June 2010

输出:

价格:

$38.00

[1] W. Przybylski: Technologia obróbki nagniataniem (Wydawnictwo Naukowo - Techniczne, Warszawa 1987) (in Polish).

[2] W. Przybylski: Wpływ stanu warstwy wierzchniej na konstytuowanej przez nagniatanie na trwałość elementów maszyn. Wybrane problemy Trybologii (PWN, Warszawa 1990) (in Polish).

[3] W. Przybylski, J. Wojciechowski: Technological and organizational aspects of cleaner manufacturing. First Cleaner Production International Conference. Rydzyna 1996 (in Polish).

[4] L. Kukiełka: Teoretyczne i doświadczalne podstawy powierzchniowego nagniatania tocznego z elektrokontaktowym nagrzewaniem (Wydawnictwo Uczelniane Wyższej Szkoły Inżynierskiej, Monografia WM Nr 47, Koszalin 1994) (in Polish).

[5] A. M. Hassan: The effects ball- and roller-burnishing on the surface roughness and hardness of some non-ferrous metals. Journal of Materials Processing Technology Vol. 72 (1997), p.385391.

DOI: 10.1016/s0924-0136(97)00199-4

[6] K. Tubielewicz: Technologia nagniatania żeliwnych części maszynowych (Wydawnictwa Politechniki Częstochowskiej, Monografie No 69, Częstochowa 2000) (in Polish).

[7] R. Melechow, K. Tubielewicz, W. Błaszczuk: Tytan i jego stopy (Wydawnictwa Politechniki Częstochowskiej, Monografie Nr 107, Częstochowa 2004) , pp.197-205, (in Polish).

[8] L.N. López de Lacalle, A. Lamikiz, J. Muñoa, J.A. Sánchez: Quality improvement of ball-end milled sculptured surfaces by ball burnishing. International Journal of Machine Tools & Manufacture Vol. 45 (2005), pp.1659-1668.

DOI: 10.1016/j.ijmachtools.2005.03.007

[9] N.S.M. El-Tayeb, K. O Low, P. V Brevern: Influence of roller burnishing contact width and burnishing orientation on surface quality and tribological behaviour of Aluminium 6061, Journal of Materials Processing Technology Vol. 186 (2007).

DOI: 10.1016/j.jmatprotec.2006.12.044

[10] P. J. Golden, A. Hutson, V. Sundaram, J. H Arps: Effect of surface treatments on fretting fatigue of Ti-6Al-4V, International Journal of Fatigue Vol. 29 (2007), pp.1302-1310.

DOI: 10.1016/j.ijfatigue.2006.10.005

为了查看相关信息, 需 Login.